Skip to content
Ground-mounted solar array powering a remote mining site

Containerised — BK-PLTS-MOB

Deployable

Mobile PLTS — Remote Area

Containerised solar power that can be transported, deployed, and relocated as the site moves.

A complete solar-plus-storage power unit built around a transportable container. Fold-out PV arrays, inverter, battery, and controls arrive together and can be commissioned in the field — then moved again when the project does.

Free load study25-year panel warrantyIndonesia-wide

Rapid

Field deployment

1

Container base unit

24/7

Remote monitoring

Move

Relocatable asset

The package

What Mobile PLTS
is built for.

Mobile PLTS is for sites that need power now and may not stay in one place: exploration camps, construction villages, disaster response, temporary telecom, and agricultural operations. The container protects the electronics in transit and becomes the plant room on site.

The array unfolds from the container or is ground-mounted beside it, depending on the terrain. The unit can run as a stand-alone microgrid or synchronise with an existing genset, and it can be expanded by paralleling additional containers as the load grows.

Because it is a repeatable product rather than a one-off build, it can be specified, shipped, and commissioned faster than a fixed installation. Remote monitoring lets the head office see generation, battery state, and load from day one.

Best for

  • Mining exploration
  • Construction camp
  • Disaster response
  • Telecommunications
  • Agriculture
  • Temporary event

At a glance

  • — Containerised, transport-ready power unit
  • — Fold-out or ground-mounted array
  • — Battery storage included
  • — Genset synchronisation optional

Field deployment

Packed, shipped, deployed.

Containerised mobile PLTS unit with a fold-out solar array
Container, inverter, battery, and fold-out array arrive as one transportable power unit.

What is included

Everything in the
Mobile PLTS package.

  • — Containerised inverter and battery skid
  • — Fold-out or ground-mounted PV array
  • — Rapid-deploy mounting and cabling
  • — MPPT charge control and protection
  • — Energy management and remote monitoring
  • — Transport, commissioning, and operator training

Final capacity, Bill of Materials, and price are confirmed after the free technical feasibility study. No payment is taken on this page.

Scale check

What 1 kW to 1 MW looks like.

This is the same sizing instrument used across the PLTS family, pre-set to the load profile that suits Mobile PLTS.

Sizing instrument

From 1 kW to 1 MW.

Pick a load profile, then move along the rail. Each setting shows the PV array, usable battery, module count, inverter count, and mounting area you would expect for that scale.

Indicative pre-feasibility

Remote sites, islands, camps

100 kWp

Indicative design

100 kWp

24-hour profile · 24 h/day

Usable BESS
340 kWh
Load served
14 kW
Send this sizing on WhatsApp →
Daily generation
336 kWh
Load served
14 kW
Usable BESS
340 kWh
650 Wp modules
154 units
Inverters
2 × 50 kW
Mounting area
400 m²
Annual yield
123 MWh
CO₂ avoided
107 t/yr

Indicative only: 4.2 peak-sun hours per day, 80% performance ratio, 650 Wp modules at 2.6 m² each including access, tiered string inverters, and a 0.87 t CO₂/MWh grid factor. A measured load study sets the final design.

100 kilowatt peak, 24-hour profile, 340 kilowatt-hour battery, 154 modules, 2 inverters.

The common standard

Every package is engineered, not assembled.

Each Bamantara PLTS package starts with a load study and a single-line electrical design. Tier-1 monocrystalline modules, IEC/SNI protection, structural mounting, commissioning, and remote monitoring are included as standard. The final scope and price are confirmed after a free site survey — no estimate on this page replaces a stamped design.

  • — Load study and single-line electrical design before pricing
  • — Tier-1 monocrystalline modules with a 25-year performance warranty
  • — IEC/SNI protection, earthing, and surge devices
  • — Structural mounting designed for local wind and roof loads
  • — Commissioning, as-built documentation, and remote monitoring
  • — Free site survey and technical feasibility study across Indonesia

FAQ

Questions about Mobile PLTS.

How fast can a Mobile PLTS be deployed?
The container arrives pre-assembled and pre-tested. Site work is mainly positioning, unfolding or mounting the array, and commissioning. Deployment time depends on terrain and array size, so the proposal states a target schedule after the site survey.
Can it be moved after installation?
Yes. The power unit is designed to be de-rigged, lifted, and transported to the next site. Mounting and cabling are selected for repeat deployment rather than a permanent build.
How much power does one container provide?
Capacity depends on the array and battery configuration specified. A single container can be sized for a camp or telecom load, and multiple containers can be paralleled when the site needs more power.
Does it work in remote or harsh terrain?
Yes. The enclosure protects the electronics from dust, rain, and transport vibration. We select IP ratings, mounting, and array foundations for the specific site conditions.

Send the load.
We will size the plant.

Share your site, load profile, and operating hours. Our engineers will return a technical feasibility study and a Mobile PLTS recommendation.